Powder metallurgy (P/M) consists of making solid parts out of metal powders. The powder is mixed with a lubricant, pressed into a die to form the desired shape, and then sintered, or heated to a temperature below the melting point of the alloy where solid-state bonding of the particles takes place. In the absence of any external force, sintering typically leaves the sample containing about 5 percent pores by volume, but, when pressure is applied during sintering (a process called hot pressing), virtually zero porosity remains. In some parts made by mixing two different elements, one component melts at the sintering temperature, and this liquid phase aids sintering of the solid particles.
Applications
The following roughly chronological account indicates the types of products that can be made by P/M.
The earliest commercial use of P/M was in the production of such high-melting-point metals as platinum, tungsten, and tantalum. Pure powders of these metals could be made by the low-temperature reduction of powders, usually oxides, and, since these metals melt at extremely high temperatures, it was easier to form solid parts by pressing and sintering the powders than by melting and casting. For example, P/M played an important role in the development of tungsten filaments for electric light bulbs.
Another early P/M product was porous-metal bearings and filters. In such parts sintering is conducted at a relatively low temperature so that the pores between the particles remain open and connected. Disks sintered in this way can serve as filters for liquids, or the sintered part can be impregnated with oil to make a self-lubricating bearing. In the latter case, the oil is held in the pores by surface tension. When the bearing heats up in use, some oil flows out and lubricates the surface, and, when the part cools, surface tension pulls the oil back into the fine channels.
Cemented carbides form another class of sintered product. Pure tungsten carbide (WC) is an extremely hard compound, but it is too brittle to be used in tools. However, useful tools can be made by mixing WC powder with cobalt powder and sintering at a temperature above the melting point of cobalt. Liquid cobalt then reacts with the surface of the WC, and when the part is cooled the cobalt freezes, holding the WC tightly together to form a composite structure with enough toughness to be used for tools and dies.
The greatest volume of P/M parts is now produced from iron powder, a process that was first developed during World War II. Small, complex parts, such as gears, require much work if machined from steel bars, and a significant volume of material is wasted as chips from the machining. However, if the part is made by P/M processes, little or no machining is necessary, there is less wasted material, and the cost is much lower. Many small parts for automobiles and appliances are produced in this manner. The second greatest volume of P/M parts is made from aluminum powder. These parts are light, corrosion-resistant, and (if alloy is used) can be heat treated to appreciably increase the strength. Small parts for automobiles and appliances are the most common applications.
A recent process uses P/M methods to improve the homogeneity and toughness of high-alloy tool steels. Cast ingots of these alloys contain a coarse network of brittle phases that are very difficult to break up by hot working, but if, instead of being cast into ingots, the liquid is atomized (solidified as small droplets), the rapidly solidified particles will be homogeneous. This powder can then be hot pressed into consolidated bars with better mechanical properties than those produced by ingot casting. Consolidation is often achieved by hot isostatic pressing, wrapping the pressed powder in an envelope of steel or glass, and heating it in a hot inert gas at high pressure. The consolidated metal is then worked into finished parts.
Processes
The most common method of producing metal powders is atomization of a liquid. Here a stream of molten metal is broken up into small droplets with a jet of water, air, or inert gas such as nitrogen or argon. Atomization in water yields irregularly shaped particles that can be pressed to a higher initial, or “green,” strength and density than can the spherical particles formed by atomizing with an inert gas.
In other atomization processes, centrifugal force is used. The metal can be poured onto a spinning disk that breaks up the stream, or a spinning rod can be melted by an electric arc so that it throws off particles as it spins.
The liquid metal being atomized may be an alloy or a pure metal that will subsequently be blended with other elements to form an alloy. After atomization, the powder must be separated into size ranges by passing it through a series of sieves. Powders of different sizes (and of different metals) are then blended for pressing into parts.
Powders are often produced by chemically reducing a powdered oxide—for example, iron oxide reduced with carbon or hydrogen. The resulting metal aggregate is then milled and sieved to obtain the desired powder. Powder also can be made by electrodepositing the metal at a high current density, followed by milling to break up the deposit.
The above processes often produce powders that are roughly 50 to 200 micrometres in diameter. Powders less than one-tenth this size can be found in the finest fraction of the powder produced by atomization. Such fine powders can be mixed with a wax, injection molded to form several parts at once, and then sintered. The resulting parts require very little machining to yield a finished product.